Streszczenie treści zawartej na stronie nr. 1
10/100Base-TX to 100Base-FX
Redundant Media Converter
FT-1105A / FT-1205A
User’s Manual
Streszczenie treści zawartej na stronie nr. 2
Trademarks Copyright © PLANET Technology Corp. 2007. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a
Streszczenie treści zawartej na stronie nr. 3
FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communication
Streszczenie treści zawartej na stronie nr. 4
Revision PLANET Fast Ethernet Redundant Media Converter User’s Manual FOR MODELS: FT-1105A / FT-1205A Revision: 1.1 (November, 2007) Part No.: 2010-AA3520-002
Streszczenie treści zawartej na stronie nr. 5
Table of Contents Chapter 1 OVERVIEW ............................................................6 Chapter 2 PRODUCT FEATURES ..............................................8 Chapter 3 CHECKLIST ......................................................... 10 Chapter 4 PRODUCT OUTLOOK ............................................ 11 Chapter 5 DIP SWITCH ....................................................... 12 Chapter 6 INSTALLING THE CONVERTER ............................. 14 6.1 Stand-alone Insta
Streszczenie treści zawartej na stronie nr. 6
Chapter 1 OVERVIEW Thank you for choosing the Smart 10/100Base-TX to 100Base- FX Media Converter, The Media Converter introduced here provides one channel media conversion between 10/100Base-TX and 100Base-FX. About the Redundant Media Converter The FT-1105A and FT-1205A are 3-Port Redundant Media Converters which support conversion between 10/100Base- TX and 100Base-FX network. Different with the other one-port channel media converter, the Redundant Media Converters are designed for critic
Streszczenie treści zawartej na stronie nr. 7
network. The SFP slot supports single-mode, multi-mode and WDM small-form factory type transceiver modules for your needs. With 100Base-FX SFP ports, the FT-1105A and FT-1205A are with high reliability and flexibility to extend the distance up to 2Km, 20Km, or longer. It depends on the 100Base-FX SFP transceiver modules. Ethernet signal that allows two type segments connect easily, efficiently and inexpensively. The converters can be used as a stand-alone unit or as a slide- in module to
Streszczenie treści zawartej na stronie nr. 8
Chapter 2 PRODUCT FEATURES Standard • Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX • IEEE 802.3x Full-Duplex Flow-Control, Back-Pressure in Half- Duplex eliminate packets loss Interface • FT-1105A: Dual 10/100Base-TX Copper, One 100Base-FX SFP Fiber optic ● FT-1205A: Dual 100Base-FX SFP Fiber optic, One 10/100Base-TX Copper ● Auto-Negotiation for 10/100Base-TX Half-Duplex or Full- Duplex ● Supports Auto MDI/MDI-X function ● Supports Maximum frame size up to 2046Kbytes. Redu
Streszczenie treści zawartej na stronie nr. 9
● DIP Switch for 3-Port operation with Fast Ethernet switch mode or Redundant mode ● DIP switch for LPR (Loop back Reply) on / off selection ● Compact size, easy installation ● Co-work with PLANET MC family Media Chassis (MC- 700/1000R/1500)
Streszczenie treści zawartej na stronie nr. 10
Chapter 3 CHECKLIST Your FT-1105A / FT-1205A carton should contain the following items: The Redundant Fast Ethernet Converter AC-DC Power Adapter (Output: 5VDC, 2A max.) This user’s manual If any item is missing or damaged, please consult the dealer from whom you purchased your Redundant Fast Ethernet Converter. FT-1105A / FT-1205A is with one vacant SFP module slot. The 100Base-FX SFP module is not bundled with in the package Note 10
Streszczenie treści zawartej na stronie nr. 11
Chapter 4 PRODUCT OUTLOOK FT-1105A Front Panel ● Port-1 100Base SFP slot ● Port-2 TP connector (Primary Port) ● Port-3 TP connector (Backup Port) FT-1205A Front Panel ● Port-1 100Base SFP slot (Primary Port) ● Port-2 100Base SFP slot (Backup Port) ● Port-3 TP connector FT-1105A / FT-1205A Rear Panel One DC jack for DC power input and DIP switch to set 3-Port switch mode / 2-Port Redundant and Loop back reply Enable/ Disable function. 11
Streszczenie treści zawartej na stronie nr. 12
Chapter 5 DIP SWITCH There is a DIP switch for the setting on converter mode of copper and fiber port. Refer to the table below for more details. FT-1105A On 2-Port Redundant (TP) Switch 1 Off 3-Port Switch (default) On LBR ON Switch 2 Off LBR OFF (default) 2-Port Redundant (FT-1105A) When TP Redundancy is enabled, TP Port-2 and TP Port-3 are configured as either forwarding or disabled. At any given time, one port will be disabled and one port will be forwarding. 3-Port Switch When TP Redunda
Streszczenie treści zawartej na stronie nr. 13
FT-1205A On 2-Port Redundant (Fiber) Switch 1 Off 3-Port Switch (default) On LBR ON Switch 2 Off LBR OFF (default) 2-Port Redundant (FT-1205A) When Fiber Redundancy is enabled, Fiber Port-1 (1) and Fiber Port-2 (2) are configured as either forwarding or disabled. At any given time, one port will be disabled and one port will be forwarding. 3-Port Switch When Fiber Redundancy is disabled, all ports (Port-1, Port-2 and Port-3) act as normal bridging ports. FT-1105A / FT-1205A supports OAM/TS-1
Streszczenie treści zawartej na stronie nr. 14
Chapter 6 INSTALLING THE CONVERTER 6.1 Stand-alone Installation FT-1105A / FT-1205A is with high reliability and flexibility to extend the distance up to 2Km, 20Km, or longer. It depends on the 100Base-FX SFP transceiver modules. The SFP transceivers are hot-pluggable and hot-swappable. You can plug-in and out the transceiver to/from any SFP port without having to power down the converter. To install a FT-1105A / FT-1205A stand-alone, on a desktop or shelf, simply complete the following s
Streszczenie treści zawartej na stronie nr. 15
It recommends using PLANET MFB-FX series 100Base-FX SFP on the converter. If you insert a SFP transceiver that is not supported, the Note converter will not recognize it. Step 4: Connect the fiber cable. Attach the duplex LC connector on the network cable into the SFP transceiver. Step 5: Attach fiber cable from the FT-1105A/FT-1205A to the fiber network. TX, RX must be paired at both ends. Step 6: Connect the 5VDC power adapter to the FT-1105A/FT- 1205A and verify that the Power LED lights
Streszczenie treści zawartej na stronie nr. 16
Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis. Figure 2-1: Insert a media converter into an available slot Step 3: Attach a rack-mount bracket to each side of the Chassis with supplied screws attached to the package. Step 4: After the brackets are attached to the chassis, use suitable screws to securely attach the brackets to the rack, as shown in Figure 2-2. Step 5: Proceed with the steps 4 and steps 5 of session 6.1 Stand-alone I
Streszczenie treści zawartej na stronie nr. 17
Chapter 7 Redundancy The FT-1105A / FT-1205A provide less than 10ms link redundancy for highly critical Ethernet applications. The redundant-mode supports auto-recover function. If the destination port of a packet is link down, it forwards the packet to the other port of the backup pair. The following figure shows the redundant function. Redundancy < Primary Port > Main Primary Link Status : Up Traffic Flow : Forwarding Backup < Backup Port > Link Status : Up Traffic Flow : Blocking Redun
Streszczenie treści zawartej na stronie nr. 18
Chapter 8 Loop Back Reply The FT-1105A / FT-1205A supports auto loop back reply while receive loop back test packets on fiber port. Enable this function to tell the converter to reply fiber signals request from Web Smart media converter, such as PLANET FT-90x. You can use this to check whether the converter can communicate with partner converter. Please refer to the following figure. For FT-1105A only, while enable the Loop Back Reply function, the Port-2 (TP) must be link up. Note 1
Streszczenie treści zawartej na stronie nr. 19
Chapter 9 LED INDICATORS The LED indicators give you instant feedback on status of the converter: System LED Color Function PWR Green Lit: Power on. FT-1105A / FT-1205A -10/100Base-TX Port LED Color Function Lit: Indicate that the port is link up. Indicate that the converter is LNK/ Green Blink: actively sending or receiving data ACT over that port. Off: Indicate that the port is link down. Indicate that the port is operating at Lit: 100Mbps. 100 Orange Indicate that the port is link down
Streszczenie treści zawartej na stronie nr. 20
LED Color Function Lit: Indicate that the port is link up. Indicate that the converter is LNK/ Green Blink: actively sending or receiving data ACT over that port. Off: Indicate that the port is link down. Indicate that the connection made Lit: through the corresponding port is running in Full-Duplex mode. FDX/ Green COL Indicate that the connection made Off: through the corresponding port is running in Half-Duplex mode. FT-1205A -100Base-FX SFP Port LED Color Function Lit: Indicate that t
