Instrukcja obsługi Clam Corp CLAM 5600 8201

Streszczenie treści zawartej na stronie nr. 1

M o d e l N o .
- 8 2 0 1 -
S p e c i f i c a t i o n s
H e i g h t - 7 7 i n c h es (9” packed)
▪
Depth - 7 2 i n c h es (32” packed)
▪
▪ W i d t h - 6 0 i n c h e s
W e i g h t – 7 5 l b s .
▪


p /n 108330


I n s t r u c t i o n N o . 1 0 2 4 8 6

- Cl am Cu st om er S erv i c e I n for m at i on -
NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE
A WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY AND CONTACT

Streszczenie treści zawartej na stronie nr. 2

SAFETY INSTRUCTIONS Please fully understand and follow all safety instructions outlined in this booklet. Failure to do so could result in severe injury. Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for • Do not use open flame heaters in your ice shelter. fresh air ventilation. Open vents for cross ventilation. Injury or death may result from fire if tent fabric is exposed to open flame. • Ice Armor fabric will melt when con

Streszczenie treści zawartej na stronie nr. 3

PARTS IDENTIFICATION (Parts on this page are NOT actual size.) ##27 HOOP POLE PART 101171 #28 HINGE CONNECTOR PART 101641 #26 ROUND POLE PART 101646 #25 SQUARE POLE PART 101645 #6 SPREADER TUBE PART 101186 #21 DOME POLE PART 101182 #17 A SUPPORT BRACE #18 B SUPPORT BRACE PART 101197 PART 101192 Page 3

Streszczenie treści zawartej na stronie nr. 4

PARTS IDENTIFICATION (Parts below this box ARE shown actual #15 1" WASHER #10 NYLOCK NUT #9 KEPS NUT PART 101206 PART 101163 PART 101191 #16 3/4" SCREW #24 3/4" SCREW #19 1-1/2" SCREW PART 101212 PART 101207 PART 101208 #20 CARRIAGE BOLT #23 1-3/4" BOLT PART 101209 PART 101211 Page 4

Streszczenie treści zawartej na stronie nr. 5

CLAM 5600 EXPLODED DRAWING Page 5

Streszczenie treści zawartej na stronie nr. 6

ASSEMBLY INSTRUCTIONS BEFORE ATTEMPTING TO USE THIS PRODUCT ON THE ICE practice setting up and taking down at home in the comfort of a heated area. Repeat several times until comfortable. This will make your on-ice set-up much easier. NO TOOLS ARE NEEDED FOR ASSEMBLY OF YOUR CLAM 5600. 1. INITIAL SET-UP a. Open the Clam 5600 and lay on a flat level surface. See Diagram A. b. Lift up the two hoop pole sections until the snap button locks into place. Lock the braces. See Diagram

Streszczenie treści zawartej na stronie nr. 7

ASSEMBLY INSTRUCTIONS 5. DISMANTLING YOUR CLAM a. To take your Clam 5600 down, repeat steps 1–3 in reverse order. Lay all the poles on one side of the base. Fold the tent into the base, making sure you don’ t fold or crease the windows as that could cause them to crack. See Diagram J. b. Close up the base and secure the rubber latches. See Diagram K. Note: Continuous pulling behind a four wheeler or snowmobile will result in premature wear of the base. We recommend a ski or sl

Streszczenie treści zawartej na stronie nr. 8

ASSEMBLY DIAGRAMS DIAGRAM C DIAGRAM D Spreader Tubes Page 8

Streszczenie treści zawartej na stronie nr. 9

ASSEMBLY DIAGRAMS DIAGRAM E Dome Pole DIAGRAM F DIAGRAM G DIAGRAM H Page 9

Streszczenie treści zawartej na stronie nr. 10

ASSEMBLY DIAGRAMS DIAGRAM I DIAGRAM J \ Page 10

Streszczenie treści zawartej na stronie nr. 11

- Safety Instructions - Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or death. Do not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is ▪ exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant properties ineffective. Ice

Streszczenie treści zawartej na stronie nr. 12