Instrukcja obsługi Clam Corp Fish Trap 8325

Streszczenie treści zawartej na stronie nr. 1

Model No.
- 8325 -
p/n 108325

Specifications
Height: 75” (24” packed)
▪
Width: 72”
▪
▪ Depth: 92” (40” packed)
Weight: 135 lbs.
▪
Instruction p/n 102479
▪


















- Clam Customer Servi ce Information -
NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
warranty claim, have your sales receipt ready and contact Clam Corporation
Customer Service by email inquiry or direct by calling:
Customer Service Hrs: - 9am to 4pm, M

Streszczenie treści zawartej na stronie nr. 2

- Parts Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 1 102498 BASE, VOYAGER, 08/09 1 2 101479 TUBE, PORCH HOOP 1 3 101585 BRKT, RIGHT CANOPY 1 4 101463 FOLDING SEAT ASSEMBLY 2 5 101482 TUBE, CANOPY HOOP 3 6 101130 LONG ROOF SPREADER 1 7 101124 SHORT ROOF SPREADER POLE 1 8 101458 CONSOLE, CLAM CENTER 1 9 101580 REAR SPREADER POLE 1 10 101069 POLE CANOPY, 1/2" 6 11 102504 TUBE, RAIL SUPPORT 08/09 1 12 101083 CAP, TUBE SPACER 8 13 101080 SCREW, 1/4-20 X 1.25 8 14 101081 WASHER

Streszczenie treści zawartej na stronie nr. 3

- Assembl y Diagram - 3

Streszczenie treści zawartej na stronie nr. 4

- Step One - 4

Streszczenie treści zawartej na stronie nr. 5

- Step Two - 5

Streszczenie treści zawartej na stronie nr. 6

- Step Three - 6

Streszczenie treści zawartej na stronie nr. 7

- Step Four - 7

Streszczenie treści zawartej na stronie nr. 8

- St ep Five - Rear Seat Bracket (p/n 102430) Latch Clip (p/n 102512) 8

Streszczenie treści zawartej na stronie nr. 9

- Step Six - Voyag er Base (p/n 102498) 1”x2” Rectangular Sup port Tub e (p/n 102504) 9

Streszczenie treści zawartej na stronie nr. 10

- Step Seven - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. Support the first canopy hoop pole as pictured with the rear adjustable spreader poles (the shorter of the two provided lengths). Lean the two remaining canopy hoop poles against the first. Canopy Hoop Pole (p/n 101482) 10

Streszczenie treści zawartej na stronie nr. 11

- Step Ei ght - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Orient the porch hoop pole so that the holes face upward and then feed the length of the pole through the three porch hoop sleeves sewn on the tent. Slide the porch hoop pole onto the porch poles, engaging the third hole position. Attach the porch hoop velcro on each side of the tent. Remove the rear adjustable spreader poles now support

Streszczenie treści zawartej na stronie nr. 12

- Step Nine - To “ set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip. Press the midpoint of the molding

Streszczenie treści zawartej na stronie nr. 13

- Step Ten - Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. Tilt the complete assembly downward so that the rear seat bracket lands upon the support tube. Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pushing it

Streszczenie treści zawartej na stronie nr. 14

- Tips for Use - Folding and transporting your Fish Trap is easy: Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the bottom ▪ of the base. ▪ Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. Cover with the Travel Cover* (