Streszczenie treści zawartej na stronie nr. 1
OPERATOR’S MANUAL
1/2 in. DRILL
DOUBLE INSULATED
REVERSIBLE
R7110
Your drill has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS Introduction ...................................................................................................................................................................... 2 General Safety Rules .....................................................................................................................................................3-4 Specific Safety Rules ..................................................................................................
Streszczenie treści zawartej na stronie nr. 3
GENERAL SAFETY RULES Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to WARNING: a rotating part of the power tool may result in personal Read all instructions. Failure to follow all injury. instructions listed below may result in electric shock, fire and/or serious injury. The term “power Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool tool” in all of the warnings listed
Streszczenie treści zawartej na stronie nr. 4
GENERAL SAFETY RULES When servicing a power tool, use only identical SERVICE replacement parts. Follow instructions in the Have your power tool serviced by a qualified repair Maintenance section of this manual. Use of person using only identical replacement parts. This will unauthorized parts or failure to follow Maintenance ensure that the safety of the power tool is maintained. instructions may create a risk of shock or injury. WARNING! To reduce the risk of injury, user must read
Streszczenie treści zawartej na stronie nr. 5
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n No Load Speed Rotational speed, at no load o Class II Construction Double
Streszczenie treści zawartej na stronie nr. 6
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will result DANGER: in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could result WARNING: in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in CAUTION minor or moderate injury. (Wi
Streszczenie treści zawartej na stronie nr. 7
ELECTRICAL DOUBLE INSULATION EXTENSION CORDS Double insulation is a concept in safety in electric power When using a power tool at a considerable distance from tools, which eliminates the need for the usual three-wire a power source, be sure to use an extension cord that has grounded power cord. All exposed metal parts are isolated the capacity to handle the current the tool will draw. An from the internal metal motor components with protect- undersized cord will cause a drop in line voltage
Streszczenie treści zawartej na stronie nr. 8
FEATURES PRODUCT SPECIFICATIONS Chuck .............................................................................................................................................................................1/2 in. Switch ......................................................................................................................................................................Reversible No Load Speed ...................................................................................
Streszczenie treści zawartej na stronie nr. 9
ASSEMBLY UNPACKING WARNING: This product has been shipped completely assembled. If any parts are damaged or missing do not operate Carefully remove the tool and any accessories from the this tool until the parts are replaced. Failure to box. Make sure that all items listed in the packing list are heed this warning could result in serious personal included. injury. Inspect the tool carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing mat
Streszczenie treści zawartej na stronie nr. 10
OPERATION ADJUSTING THE AUXILIARY HANDLE ASSEMBLY See Figure 2. TO TIGHTEN Unplug the drill. Loosen the auxiliary handle assembly by turning the handle counterclockwise. Rotate the auxiliary handle assembly to the desired location. Tighten the auxiliary handle assembly securely by turning the handle clockwise. TO LOOSEN SWITCH See Figure 3. To turn the drill ON, depress the switch trigger. Release the switch trigger to turn the drill OFF. AUXILIARY HANDLE ASSEMBLY DIRECTION OF ROTAT
Streszczenie treści zawartej na stronie nr. 11
OPERATION INSTALLING BITS CHUCK UNLOCK See Figure 5 - 6. BODY (RELEASE) Unplug the drill. Open or close the chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. CHUCK Also, raise the front of the drill slightly to keep the bit from JAWS falling out of the chuck jaws. Insert the drill bit. WARNING: Make sure to insert the drill bit straight into the chuck jaws. Do not insert the drill bit into the chuck jaws at an angle then tighten, as s
Streszczenie treści zawartej na stronie nr. 12
OPERATION DRILLING See Figure 8. Depress and release the switch trigger to be sure the drill is in the OFF position before connecting it to power supply. Check the direction of rotation selector for correct setting (forward or reverse). Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates. Plug the drill into power supply source. Hold the drill firmly and place the bit at the point to be drilled. Depress the switch trigger to
Streszczenie treści zawartej na stronie nr. 13
MAINTENANCE Insert hex key wrench in the chuck and tighten chuck jaws securely. WARNING: When servicing use only identical replacement Tap sharply with a mallet in a counterclockwise direc- parts. Use of any other parts may create a hazard tion. This will loosen chuck on the spindle. It can now be or cause product damage. unscrewed by hand. MALLET WARNING: Always wear safety goggles or safety glasses with CHUCK side shields during power tool operation or when JAWS blowing dust. If ope
Streszczenie treści zawartej na stronie nr. 14
MAINTENANCE Insert a hex key into the chuck and tighten chuck jaws TO RETIGHTEN A LOOSE CHUCK securely. Tap the hex key sharply with a mallet in a The chuck may become loose on the spindle and develop a clockwise direction. This will tighten the chuck on the wobble when using the drill. Periodically check chuck screw spindle. for tightness. A loose screw may cause the chuck jaws to bind and prevent them from closing. To tighten: Open the chuck jaws and remove the hex key wrench. Unpl
Streszczenie treści zawartej na stronie nr. 15
WARRANTY ® RIDGID HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting WHAT IS NOT COVERED warranty service. This warranty applies only to the original purchaser at ® retail and may not be transferred. This warranty only covers Limited to RIDGID hand held and stationary power tools defects arising under normal usage and does not cover any purchased 2/1/04 and after. This product is manufactured malfunction, failure or def
Streszczenie treści zawartej na stronie nr. 16
OPERATOR’S MANUAL 1/2 in. DRILL DOUBLE INSULATED REVERSIBLE R7110 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space p
