Streszczenie treści zawartej na stronie nr. 1
OPERATOR’S MANUAL
1/2 in. SPADE HANDLE DRILL
SINGLE SPEED/REVERSIBLE
DOUBLE INSULATED
R7121
This new drill has been engineered and manufactured to our high standard for dependability, ease of operation and operator
safety. When properly cared for, the drill will give you years of rugged, trouble-free performance.
WARNING
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUT
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS Introduction ......................................................................................................................................................................2 General Safety Rules .....................................................................................................................................................3-4 Specific Safety Rules ...................................................................................................
Streszczenie treści zawartej na stronie nr. 3
GENERAL SAFETY RULES Remove any adjusting key or wrench before turning WARNING: the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal Read all instructions. Failure to follow all injury. instructions listed below may result in electric shock, fire and/or serious injury. The term “power Do not overreach. Keep proper footing and balance tool” in all of the warnings listed below refers at all times. This enables better control of t
Streszczenie treści zawartej na stronie nr. 4
GENERAL SAFETY RULES When servicing a power tool, use only identical SERVICE replacement parts. Follow instructions in the Have your power tool serviced by a qualified repair Maintenance section of this manual. Use of person using only identical replacement parts. This will unauthorized parts or failure to follow Maintenance ensure that the safety of the power tool is maintained. instructions may create a risk of shock or injury. WARNING! To reduce the risk of injury, user must read
Streszczenie treści zawartej na stronie nr. 5
SYMBOLS Important: Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current --- n No Load Speed Rotational speed, at no load
Streszczenie treści zawartej na stronie nr. 6
ELECTRICAL DOUBLE INSULATION EXTENSION CORDS Double insulation is a concept in safety in electric power When using a power tool at a considerable distance from tools, which eliminates the need for the usual three-wire a power source, be sure to use an extension cord that has grounded power cord. All exposed metal parts are isolated the capacity to handle the current the tool will draw. An un- from the internal metal motor components with protect- dersized cord will cause a drop in line voltage
Streszczenie treści zawartej na stronie nr. 7
FEATURES SPECIFICATIONS Chuck ....................................................................................................................................................1/2 in. (13mm), Keyed Switch ............................................................................................................................................... Single Speed/Reversible No Load Speed ...............................................................................................................
Streszczenie treści zawartej na stronie nr. 8
FEATURES AUXILIARY HANDLE SPADE HANDLE CHUCK SWITCH TRIGGER / FORWARD-REVERSE LEVER LIGHTED LOCK-ON PLUG BUTTON Fig. 1 UNPACKING INSTRUCTIONS WARNING: When unpacking the drill: If any parts are missing do not operate the tool until Carefully remove the tool and accessories from the the missing parts are replaced. Failure to do so box. could result in possible serious personal injury. Make sure that all items listed in the packing list are included. Inspect the tool carefully to
Streszczenie treści zawartej na stronie nr. 9
R F ASSEMBLY WARNING: The tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. INSTALLING AUXILIARY HANDLE See Figure 2. An auxiliary handle is packed with the drill for ease of op- eration and to help prevent loss of control. The auxiliary handle may be installed at three different pos
Streszczenie treści zawartej na stronie nr. 10
ASSEMBLY TO INSTALL BITS See Figure 4. Unplug the drill. Insert the chuck key and twist counterclockwise as shown in figure 4. Insert the drill bit into the chuck the full length of the jaws. WARNING: Do not insert drill bit into chuck jaws and tighten as shown in figure 5. This could cause the drill bit to be thrown from the drill resulting in possible serious personal injury or damage to the chuck. Tighten the chuck jaws securely on the drill bit, using the chuck key provided. Do
Streszczenie treści zawartej na stronie nr. 11
OPERATION WARNING: Exercise caution when using this tool. Careless actions, for even a fraction of a second, can result in serious personal injury. APPLICATIONS You may use the spade handle drill for the purposes listed below: Drilling in wood Drilling in both hard and soft metals Using driving accessories, such as driving screws with REVERSE screwdriver bits Mixing paints and drywall compounds FORWARD WARNING: Always wear safety goggles or safety glasses with side shields wh
Streszczenie treści zawartej na stronie nr. 12
R OPERATION DRILLING See Figures 8 and 9. Attach auxiliary handle (except for very light duty jobs) Depress and release the switch trigger to be sure the drill is in the OFF position before connecting it to power supply. Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates. Plug the drill into power supply source. Hold the drill firmly and place the bit at the point to be drilled. Depress the switch trigger to start the drill
Streszczenie treści zawartej na stronie nr. 13
MAINTENANCE WARNING: This tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. CHUCK REMOVAL See Figure 10, 11, and 12. The chuck must be removed in order to use some acces- sories. To remove: Unplug the drill. Open chuck jaws using the provided chuck key. Fig. 10 Insert a 3/8 inch (
Streszczenie treści zawartej na stronie nr. 14
MAINTENANCE WARNING: This tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. BRUSH REPLACEMENT See Figure 13. The drill has externally accessible brush assemblies that should be periodically checked for wear. Follow these steps to replace the brushes: Unplug the drill. Remove the b
Streszczenie treści zawartej na stronie nr. 15
MAINTENANCE Electric tools used on fiberglass material, wallboard, spack- WARNING: ling compounds, or plaster are subject to accelerated wear ® When servicing use only identical RIDGID and possible premature failure because the fiberglass chips replacement parts. Use of any other parts may and grindings are highly abrasive to bearings, brushes, com- create a hazard or cause product damage. mutators, etc. Consequently, we do not recommended using this tool for extended work on these types of m
Streszczenie treści zawartej na stronie nr. 16
NOTES 16
Streszczenie treści zawartej na stronie nr. 17
WARRANTY ® RIDGID HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting war- WHAT IS NOT COVERED ranty service. This warranty applies only to the original purchaser at retail ® and may not be transferred. This warranty only covers de- Limited to RIDGID hand held and stationary power tools fects arising under normal usage and does not cover any purchased 2/1/04 and after. This product is manufactured malfunction, failure or d
Streszczenie treści zawartej na stronie nr. 18
OPERATOR’S MANUAL 1/2 in. SPADE HANDLE DRILL SINGLE SPEED/REVERSIBLE DOUBLE INSULATED R7121 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing. Please record the se
