Краткое содержание страницы № 1
User’s Manual
DVI DL 201 Tx/Rx
Dual Link DVI Transmitter and Receiver
68-1531-01
Rev. B
12 08
Краткое содержание страницы № 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety the literature provided with the equipment. feature, do not attempt to bypass or disable it.
Краткое содержание страницы № 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生产厂的 全和操作说明。 建议处理废弃电
Краткое содержание страницы № 4
Краткое содержание страницы № 5
Quick Start Guide — DVI DL 201 Tx/Rx The DVI DL 201 Tx/Rx extends DVI-D signals up to 100' (30 m) at resolutions up to 2560x1600 @ 60 Hz, using twisted pair (TP) cable. Install, connect, and operate the DVI DL 201 Tx/Rx as follows: Step 1 Turn off all equipment or disconnect it from power sources. Mount the transmitter and receiver as desired (see page 2-2). Step 2 Determine how the source device will obtain the EDID information and perform one of the following procedures: To capture the
Краткое содержание страницы № 6
Quick Start Guide — DVI DL 201 Tx/Rx, cont’d To use DDC pass-through routed to the local monitor: a. Configure the DDC switches as shown in the figure at right and described on page 3-4. b. Connect a source device to the transmitter. ON c. Connect a display device to the receiver and, if ON required, a local monitor to the transmitter. d. Connect the transmitter and receiver. 1 2 3 OFF e. Power on the transmitter, receiver, and local monitor. f. Power on the source device. g. Power on
Краткое содержание страницы № 7
Table of Contents Chapter One • Introduction .................................................... 1-1 About this Manual .................................................................... 1-2 About the DVI DL 201 Tx/Rx .................................................. 1-2 DVI DL 201 Tx/Rx Features ..................................................... 1-2 Chapter Two • Installation ...................................................... 2-1 Mounting the DVI DL 201 Tx/Rx ......................
Краткое содержание страницы № 8
Table of Contents, cont’d Chapter Three • Configuration and Operation ......... 3-1 Configuration .............................................................................. 3-2 Using the EDID Minder to read and store EDID from a display ..................................................................................... 3-2 Using the EDID Minder with the default EDID .................... 3-3 Using pass-through mode with DDC routed to a local monitor ......................................
Краткое содержание страницы № 9
DVI DL 201 Tx/Rx Chapter One 1 Introduction About this Manual About the DVI DL 201 Tx/Rx DVI DL 201 Tx/Rx Features
Краткое содержание страницы № 10
Introduction About this Manual This manual contains information about the DVI DL 201 Tx/Rx signal transmitter and receiver, with information on how to mount, install, and operate these units. In this manual, unless otherwise specified, the terms "DVI DL 201" or "DVI DL 201 Tx/Rx" refer to both the transmitter (DVI DL 201 Tx) and the receiver (DVI DL 201 Rx). The term "transmitter" refers to the DVI DL 201 Tx, and "receiver" refers to the DVI DL 201 Rx. About the DVI DL 201 Tx/Rx The DVI
Краткое содержание страницы № 11
EDID Minder — The EDID Minder maintains continuous EDID (Extended Display Identification Data) communication with the attached source. This ensures that the DVI source powers up correctly and maintains a proper video output, even if the display is off. Control communications pass-through — The DVI DL 201 passes through RS-232 (two way) or IR (one way) control signals, to a remote display. Compact design — The transmitter is 1U high, a half rack wide and 3" deep, for easy rack mounting
Краткое содержание страницы № 12
Introduction, cont’d 1-4 DVI DL 201 Tx/Rx • Introduction
Краткое содержание страницы № 13
DVI DL 201 Tx/Rx Chapter Two 2 Installation Mounting the DVI DL 201 Tx/Rx Panel Features Cable Connections and Switches
Краткое содержание страницы № 14
Installation Mounting the DVI DL 201 Tx/Rx The transmitter is 1U high, a half rack wide and 3" deep, for easy rack mounting near the source device. The receiver is 1" high, a quarter rack wide and 3" deep, allowing multiple mounting options near the display device. Tabletop placement Attach the four included rubber feet to the bottom of the unit and place it in any convenient location. Rack mounting UL guidelines for rack mounting The following Underwriters Laboratories (UL) guidelines are r
Краткое содержание страницы № 15
Rack mounting procedures The unit can be mounted in the front or rear of: • RSU 126 (6" deep 1U universal rack shelf kit: PN 60-190-10) • RSB 126 (6" deep 1U basic rack shelf: PN 60-604-10) • RSU 129 (9.5" deep 1U universal rack shelf kit: PN 60-190-01) • RSB 129 (9.5" deep 1U basic rack shelf: PN 60-604-01) To mount the unit, follow these instructions: 1. Remove rubber feet if these have been installed on the bottom of the unit. 2. Align the unit on the shelf and secure it to the shelf with
Краткое содержание страницы № 16
Installation, cont’d Under-desk mounting The figure below shows how to mount the DVI DL 201 Tx under a desk or podium, using the optional Extron MBU 123 under desk mounting kit (PN 70-212-01). To mount the DVI DL 201 Rx, the optional Extron MBU 125 under desk mounting kit (PN 70-077-01, not shown) must be used. For either unit, follow these instructions: 1. Remove rubber feet if these have been installed on the bottom of the unit. 2. Secure the mounting brackets to the unit, using the f
Краткое содержание страницы № 17
Through-desk mounting The DVI DL 201 Tx should not be mounted through a desk. To mount the DVI DL 201 Rx through a desk or podium, use the optional Extron MBD 129 through-desk mounting kit (PN 70-077-02), and follow these instructions: 1. Remove rubber feet if these have been installed on the bottom of the unit. 2. Attach the brackets to the receiver, using the four 4-40 screws provided; leave the screws slightly loose. Through-desk mounting the DVI DL 201 Rx 3. Hold the unit in position
Краткое содержание страницы № 18
Installation, cont’d Pole mounting The instructions for mounting the receiver on the projector pole, using the PMK 300 pole mounting kit (PN 70-374-01), are shown below. For instructions on using any other Extron projector mounting kit, consult the appropriate user guide. 1. If necessary, remove the rubber feet from the bottom of the DVI DL 201 Rx. 2. Mount the receiver to any of the bracket's three mounting plates. The unit should be vertically mounted with the front panel (DVI output)
Краткое содержание страницы № 19
On the side mounting plates, the device is typically N mounted on the outside of the bracket. On the front mounting plate, the device is mounted on the inside of the bracket. a. Use the two 4-40 x 3/16" screws (provided) to secure the receiver to the bracket b. If required, secure the power supply using the plastic ties provided with the kit. The projector pole can be clamped to the back surface of N the clamping plate on the PMK 300, as shown in the figure on the previous page. Alt
Краткое содержание страницы № 20
Installation, cont’d Panel Features DVI DL 201 Tx front panel features The illustration below shows the front panel features of the DVI DL 201 Tx. DVI DL 201 Tx DVI DUAL LINK TRANSMITTER 1 DVI DL 201 Tx front panel features LED — An amber light indicates that the DVI DL 201 Tx is a receiving power from a power supply or remotely, through the receiver. A green light indicates that the transmitter is also receiving a video signal. 2-8 DVI DL 201 Tx/Rx • Installation
