ملخص المحتوى في الصفحة رقم 1
LP Gas Grill Assembly and Use Manual
With the NEW Aussie
FLAVOR ACTIVATOR SYSTEM
(Patent Pending)
Provides:
- More even heat on the cooking surface
- Hotter temperature with the same fuel usage
- Longer cooking for the same amount of fuel
67C3C8KK81
67C3C8LK81
67C3C8MM81
For Outdoor Household Use Only. Not for Commercial Use.
Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?
Visit us online at www.AussieGrills.com Or call Aussie Customer Service at 1-800-251-7558
WA
ملخص المحتوى في الصفحة رقم 2
2 NOTICE Meco Corporation strives to be a quality supplier of consumer products. If we omitted any parts needed for assembly, or you need troubleshooting information, please contact us using our toll free number or visit our web site. It is important to register your grill and retain your receipt. 1-800-251-7558 Consumer Service Department 8 am - 5 pm E.S.T. Monday - Friday MECO CORPORATION 1-423-639-1171 (Telephone) 1500 Industrial Road 1-423-639-2570 (Fax) Greeneville, TN 37745 USA www.aus
ملخص المحتوى في الصفحة رقم 3
3 Packing List Description 9 Warming Rack Cooking Grid, 3 pcs. Large Flavor Activator, 3 pcs. Small Flavor Activator, 4 pcs. Left Side Shelf with Side Burner Side Burner Control Knob Hood/Body Right Side Shelf Bottom Body Panel Grease Pan Foil Pan Front Crossbar Left Side Frame Back Panel Cylinder Retainer Bolt Cart Bottom Panel Cylinder Blocking Wire Right Side Frame Locking Casters, 2 pcs. Casters, 2 pcs Caster Caps, 2 pcs. Door Handle Door Hardware Package Detailed Parts List and Illustrati
ملخص المحتوى في الصفحة رقم 4
4 Contents Packing Lists ................................................................ 3 Before Using Your Grill Installation Codes ....................................................... 15 Preparation for Assembly ..........................................4 Selecting a Location ................................................... 15 Assembly Instructions How to Perform a Leak Test ........................................ 16 Step 1 Caster Assembly ............................................5
ملخص المحتوى في الصفحة رقم 5
5 Assembly Instructions Step 1 Caster Assembly Identify Side Frame assemblies and lay on floor as shown. Thread stem of locking casters into nut on extension on bot- tom of front legs. Thread stems of non-locking casters into inserts in ends of back legs. Hole in side panel indicates Left Side Frame. Extension on Front Leg Locking Casters Step 2 Back Panel to Bottom Shelf Assembly Attach Back Panel to Bottom Shelf with four 1/4-20 x 0.5” bolts. Note: Flat face of Back Panel is flush with outsid
ملخص المحتوى في الصفحة رقم 6
6 7 Step 3 Cart Frame Assembly Attach Left Leg Frame and Right Leg Frame to Cart Bottom Panel with eight 1/4-20 x 1.50” Bolts. Fit one Frame onto Bottom Panel at a time and insert the 1.50” bolts through the Legs into the sides of the Bottom Panel. Attach the Back legs to the Back Panel with four 5/32-30 x .31” bolts. Tighten all securely. 1/4-20 x 1.50” Bolt set 8 pc 5/32 x .31” Bolt set 4 pc WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: Never remove
ملخص المحتوى في الصفحة رقم 7
7 Step 5 Front Crossbar and Caster Cap Assembly A. Attach the Front Crossbar between the Front Legs with four 1/4-20 x 1.50” bolts. Insert the bolts throught he out- side of the legs and into the threaded holes in the crossbar ends. Front crossbar should be oriented with the open side facing the inside of the cabinet and the hinge pin hole on the bottom. B. Install the Caster Caps on the exposed threaded stems of the front casters. A B 1/4-20 x 1.50” Bolt set 4 pc Step 6 Door handle Assembly an
ملخص المحتوى في الصفحة رقم 8
8 CAUTION ! To reduce the risk of bodily injury from lifting, the following assembly steps #s 7 and 8 will require two people. Step 7 Hood/Body To Cart Assembly Lift the Hood/Body Assembly over the cart assembly and set it down until it rests on the top of the cart legs. Align the holes in the side of the Body with the holes in the legs. Insert two 1/4-20 x .50 Bolts through the holes in the firebox flanges (Back Left Side View) and into threaded inserts in the inside face of the back legs. Ins
ملخص المحتوى في الصفحة رقم 9
9 CAUTION ! Prior to performing any further assembly, PERFORM “FIRST TIME USE” LEAK TEST as detailed on pages 16-17. If the grill is fully assembled before performing the First Time Use leak test, the side tables will need to be removed in order to perform the leak test on the main burner valves inside the control panel, behind the knobs, . Step 8 Side Table Assembly A. Screw two 1/4-20 x .50” Bolts into the two bottom threaded inserts on the outside of the Bowl. Do not screw Bolts all the w
ملخص المحتوى في الصفحة رقم 10
10 Step 9 Side Burner Valve Assembly NOTE: Side Burner Valve is already attached to the regulator hose. Hose is not shown in some illustrations for clarity. A. Install the Side Burner Valve from underneath the LEFT Side Table. Remove the screws from the side burner bracket and set aside with bracket. B. Tilt venturi end of burner down. Rotate the rectangular venturi windscreen sideways and slide toward back of grill to expose open end of burner tube. C. Insert the valve stem out through the ho
ملخص المحتوى في الصفحة رقم 11
11 Step 11 A. Side Burner Control Knob Assembly Align the flat keyed hole in the Control Knob with the keyed stem of the Side Burner Valve. Push the Control Knob onto the Side Burner Valve stem. B. Side Burner Grid Assembly Place the Side Burner Grid onto Side Burner Table, allowing the three protruded ends to fall into the three holes around the Side Burner. A B Step 12 A. Bottom Body Panel Assembly Slide the Bottom Body Panel into the guides of the Body assembly. Secure Bottom Body Panel to
ملخص المحتوى في الصفحة رقم 12
12 CAUTION ! To reduce the risk of a laceration hazard: • Wear protective gloves when installing warming rack. Hood and Bowl edges could be sharp. Step 13 Warming Rack / Flavor Activator / Cooking Grid Assembly A. Insert Warming Rack leg ends into holes on top edge of firebox. Seat securely. B. Lay a large Flavor Activator over each Burner on the lower body ridges. Lay two small Flavor Activators between each large Flavor Activator. Each Flavor Activator has individual guides on the body ridges
ملخص المحتوى في الصفحة رقم 13
13 Connecting/Disconnecting the Gas Using Gas DANGER ! Carbon Monoxide Hazard • This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. • Never use this appliance indoors, on recreational vehicles, or boats. WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: • Use only propane gas with this LP gas grill. • Do not attempt to convert an LP unit to natural gas. • Always use a gas appliance outdoors in an open area
ملخص المحتوى في الصفحة رقم 14
14 LP Hose and Regulator NOTE: WARNING ! If the hose/regulator assembly is not working properly and you need a replacement, contact Customer Service To reduce the risk of serious bodily injury or death at 1-800-251-7558 or go to www.aussiegrills.com. from fire or explosion: Be sure to have the grill model number and serial • Clean and inspect the gas hose/regulator before number printed on the black label, located inside the each use of the outdoor cooking gas appliance. left door of the
ملخص المحتوى في الصفحة رقم 15
15 Before Using Your LP Gas Grill Installation Codes WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: • This installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54 Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2 or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192 and CSA Z240 RV Series, recreational Vehicle C
ملخص المحتوى في الصفحة رقم 16
16 How to Perform A Leak Test “FIRST TIME USE” and as required Supplies Needed for a Leak Test: • Clean paint brush • Water • Dish washing liquid 1. Use an LP Gas Cylinder equipped with an OPD (Overfill Prevention Device) and have it filled at an authorized LP gas dealer by a qualified attendant. 2. Make sure all grill Control Panel Knobs are turned to the “Off” position and verify that the LP Gas Cylinder valve is closed by turning the knob on the LP Gas Cylinder clockwise until it stops. 3.
ملخص المحتوى في الصفحة رقم 17
17 6. Check for leaks by brushing the soap solution on all gas valves, hose connections and fittings. (Shown by the heavy arrows in Fig. 4, 5, and 6) Make sure you generously brush the locations with the soap solution, completely sur- rounding the connections and fittings. Fig. 5 Fig. 5a NOTE: After checking the connections and fittings in Figure 4, replace the control panel in the same manner as it was removed. Take special care to be sure the valve ends are inserted into the openings in the
ملخص المحتوى في الصفحة رقم 18
18 Lighting the Grill Using the Pulse-Spark Ignitor WARNING ! To reduce the risk of death or serious injury from an explosion or a fire beneath the grill: • Inspect and clean Burner/Venturi Tubes for insects or insect nests. Spiders or small insects can build nests, webs, and lay eggs in the grill’s Venturi Tubes, (Fig 15, page 27) obstructing the flow of gas to the Burner. The backed-up gas can ignite behind the Control Panel and cause a fire beneath the grill, posing the risk of death or ser
ملخص المحتوى في الصفحة رقم 19
19 5. Push the Igniter Button in until the Burner is lit. Listen for the spark ignition, and look to make sure the Burner is lit. If no spark, see Troubleshooting Section on page 30. 3/16” gap Gas Collector Box - If no spark, pinch together or open Gas Collector Box to adjust 3/16” gap between electrode tip and V-notch. Fig. 10 6. From the “Off” position, light all other Burners from left to right, making sure each Burner is lit before lighting the next. Your grill has a Crossover Ignition
ملخص المحتوى في الصفحة رقم 20
20 Manually Lighting the Grill WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: • Open Hood before lighting the grill to prevent an explosion from gas build-up. 1. Open the Hood. 2. IMPORTANT: Make sure Control Knobs are turned “Off.” (Fig. 7 - P.18) 3. Turn the LP Gas Cylinder valve open counterclockwise until it stops. (Fig. 8- P.18) 4. Locate either the left or right match-lighting hole you intend to use underneath the Grill Bowl. Push in and turn either
