ページ1に含まれる内容の要旨
User's Manual
RoHS
ページ2に含まれる内容の要旨
SATA SATA Package Contents: EZ SWAP 4 – Removable Hard Drive Rack 1 EZ Swap 4 2 Key 1 2 3 SATA Cable 4 Installation Screws 5 User’s Manual 3 4 5 *All other third-party brands and names are the property of their respective owners.
ページ3に含まれる内容の要旨
Table of Contents: 1. Introduction 03 2. Features/ Specifications 04 3. System Requirements 05 4. Parts Layout 06 5. Installation 07 6. Installing a Hard Drive 09 7. LCD Display 10 8. Warranty/Contact 11 Table of Content 1
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
Intel PentiumII 350 MHz-compatible Mac G3 processor & greater. MAC OS 8.6 or greater Microsoft Windows 2000/XP/VISTA/7 /7 1. SATA-equipped system. 1. SATA-equipped system. 2. For SATA speeds, the system must 2. For SATA speeds , the system must support SATA speci cations. tions. System Requirements 5
ページ7に含まれる内容の要旨
4. Parts Layout EZ SWAP 4 – Removable Hard Drive Rack Lock Door LCD Display Screws hole Fan Control Power port SATA port Fan Parts Layout 6
ページ8に含まれる内容の要旨
5. Installation EZ SWAP 4 – Removable Hard Drive Rack Power down the computer and disconnect the power cable. (Figure 5-A) (Figure 5-A) 2. Dismantle the left & right side of PC cover. (Figure 5-B) (Figure 5-B) 3. Dismantle the front cover of PC. (Figure 5-C) (Figure 5-C) 4. Insert the EZ Swap 4 into the 5.25" bay of the computer. (Figure 5-D) (Figure 5-D) Installation 7
ページ9に含まれる内容の要旨
SATA 5. Tighten the screws to ensure EZ Swap 4 is secure to the case. (Figure 5-E) (Figure 5-E) 6. Plug one side of SATA cable into a SATA port on the motherboard, plug the other side into the EZ Swap 4. (Figure 5-F & 5-G) (Figure 5-F) 7. Connect the 4 pin power cable to the EZ Swap 4's power connector. (Figure 5-G) Power Cable SATA Cable (Figure 5-G) 8. Reassemble the case and reconnect the power cable of the computer. (Figure 5-H) (Figure 5-H) Installation 8
ページ10に含まれる内容の要旨
6. Installing a Hard Drive EZ SWAP 4 – Removable Hard Drive Rack 1. Use the key to unlock the EZ Swap 4 and then open the panel. ( Figure 6-A ) ( Figure 6-A ) 2. Insert the SATA hard drive. ( Figure 6-B ) ( Figure 6-B) 3. Close the panel. ( Figure 6-C ) ( Figure 6-C ) 4. Use the key to lock the EZ Swap 4 to fully activate the EZ Swap 4. ( Figure 6-D ) NOTE : EZ Swap 4 has a power security function. When there is no hard drive present, the EZ Swap 4 will not power on. ( Figure 6-D
ページ11に含まれる内容の要旨
7. LCD Display Function Temperature Display Thermometer HDD Indicator Fan State Indicator Fan RPM Fan Settings Thermometer When critical temperatures are reached, the thermometer will flash. When the fan is functioning properly, the fan state indicator will have a spinning Fan State Indicator motion. When the fan is working improperly, the fan state indicator will flash. Temperature of the hard drive will be displayed in either ℃ and ℉. Temperature Display (Pre
ページ12に含まれる内容の要旨
8. Warranty / Contact The EZ SWAP 4 comes with a 1 year limited warranty (90 day parts). If your unit should become defective within that time frame, please go to http://www.vantecusa.com for information on how to receive warranty exchange or repair. Cosmetic defects and missing parts are not covered under this warranty. Please check the contents of the unit to make sure you received all parts. Also, check for any cosmetic a ws. If any parts are missing or if there are cosmetic defects,
