Summary of the content on the page No. 1
®
AVerMedia EB1004 BAK
Real-time Security DVR
Operations Manual
P/N: 300AABLP
MADE IN TAIWAN
Summary of the content on the page No. 2
FCC NOTICE This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial, industrial or business environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there i
Summary of the content on the page No. 3
TIME SET .............................................................................................18 Table of Contents VGA SETUP .........................................................................................19 MOTION SETUP..................................................................................19 Introduction .........................................................................................................3 HARD DRIVE SETUP ................................
Summary of the content on the page No. 4
• Full-screen resolution: Introduction Display: 720 x 480 (NTSC), 720 x 576 (PAL) Recording: 640 x 224 (NTSC), 640 x 272 (PAL) EB1004 BAK is a stand-alone, non-PC based DVR unit that provides real-time • Display and recording frame rate: monitoring and digital recording of surveillance video. Up to four video Quad mode: 30/25 fps (NTSC/PAL) per channel, total of 120/100 fps cameras and four sensor devices can be hooked up to this DVR unit. It is also (NTSC/PAL) equipped with an
Summary of the content on the page No. 5
6 : Back Panel (a) Display Channel 1 in full-screen. (b) When in the OSD menu, pressing button is equivalent to entering the number "1". 1 2 3 4 6 5 7 : (a) Display Channel 2 in full-screen. (b) Pressing this button is equivalent to entering the number "2" when in the OSD menu. 8 : (a) Display Channel 3 in full-screen. (b) Pressing this button is equivalent to entering the number "3" when in the OSD menu. 9 : 1 VIDEO OUT (BNC) : Composite video output for con
Summary of the content on the page No. 6
Install the Hard Drive in a Removable Case Install a Removable Hard Drive Case in a PC (Optional) 1. Remove the removable hard For users who purchase an optional hard drive case, please follow the steps to drive drawer from the case. install the case in a PC. 1. Power off your PC and remove the cover of your PC. 2. Remove a front cover and free a 5 1/4” drive bay. Insert the hard disk holder. Mount the hard disk holder, screw up the holder, and connect the IDE slot and power con
Summary of the content on the page No. 7
Connect the video output of each video camera or composite video source Operating the DVR Unit to the CH1 ~ CH4 connectors. • VGA monitor First Time Use Connect a VGA monitor to the VGA OUT connector of the DVR unit to use as a display for video surveillance and playback. Connecting the DVR unit to a power outlet automatically turns on its power. When the DVR unit is newly installed or replaced with hard drive(s), the hard • Power adapter drive(s) will automatically be formatted.
Summary of the content on the page No. 8
Use the following front panel buttons to select the desired video camera to display in full screen: CH1: Camera 1 CH2: Camera 2 CH3: Camera 3 CH4: Camera 4 2 If you want to switch to the other hard drive or search for a range of Note: The recording mode can be selected in the OSD main menu. video recordings, press . The ">" arrowhead cursor will then move up to the top of the screen. Video Recording and Playback To record surveillance video: 1 To customi
Summary of the content on the page No. 9
MAIN MENU Setup Menu 1 Press the MENU button to display the OSD main menu. MAIN MENU MAIN MENU > CAMERA SELECT 1234 RECORD SCHEDULE RECORD SELECT 1234 > CAMERA SELECT 1234 RECORD MODE EACH v RECORD SELECT 1234 RECORD FRAMERATE 30 +TTTSSSSSTTTTMMMMTTTTT+ RECORD MODE EACH VIDEO QUALITY NORMAL | | | | | | | | | RECORD SCHEDULE 0 3 6 9 12 15 18 21 24 RECORD FRAMERATE 30 SUBM
Summary of the content on the page No. 10
(1 2 3 4) : Switch on all camera displays. VIDEO QUALITY (1 - - 4) : Switch on camera display 1 and 4 only. There are three video quality settings to choose from: BEST, GOOD or (- 2 3 -) : Switch on camera display 2 and 3 only. NORMAL. (- - - -) : Disable all camera displays. Choosing NORMAL allows you to save more on hard drive space, but the quality of recorded video images is moderate. RECORD SELECT This determines which of the cameras surveillance video will be recorded
Summary of the content on the page No. 11
The factory default password is "111111". Use the following front panel To customize the recording schedule: buttons to input a numeric password: 1 Each number in the PROGRAMMED RECORD menu represents the time schedule (in hours) for recording, and the "v" cursor indicates the For "1" For "2" For "3" For "4" time that is selected. Press or to move through the time schedules. 2 Press the SELECT button repeatedly to cycle through these settings: ( T ) For automatic non-sto
Summary of the content on the page No. 12
VGA SETUP To setup all camera, press . You will see the screen shows MOTION CAMERA 1 2 3 4. Press the same button again to cancel VGA SETUP the setting. > RESOLUTION 1024 ^ 768 REFRESH RATE 60HZ To setup channel 1 and 4 only, press . You will see the screen shows MOTION CAMERA 1 4.Press the same buttons again to cancel the setting. PRESS (< , >), THEN(SELECT) PRESS (MENU) TO EXIT To setup channel 2 and 3 only, press . You will see the screen s
Summary of the content on the page No. 13
HARD DRIVE SETUP SENSOR SETUP HARD DRIVE SETUP SENSOR SETUP > OVERWRITE ENABLED YES > SENSOR RECORD TIME 15 MASTER HDD SIZE 80072MB ALARM OUT TIME 05 MASTER HDD USED 16014MB 20% MASTER HDD FORMAT CHANNEL 1 NORMAL-CLOSE SLAVE HDD SIZE N/A CHANNEL 2 NORMAL-OPEN SLAVE HDD USED N/A CHANNEL 3 NOT INSTALLED SLAVE HDD FORMAT CHANNEL 4 NOT INSTALLED PRESS (< , >), THEN(SELECT) PRESS (< , >), THEN(SELECT) PRESS (
Summary of the content on the page No. 14
3. Select a language. Click Connect to a PC Next to continue the installation. EB1004 BAK provides a convenient tool to trace back the recorded surveillance video, catch specific images and save as AVI files. With the EB-DVR Playback Application, users can play back the surveillance video, catch images and backup all recorded images easily . First Time Use 4. Please click Browser.. to Connecting DVR unit to a power outlet automatically turns on its power. Plug a change the dire
Summary of the content on the page No. 15
5. Backward play: Play the video backward. Operating EB-DVR Playback Application 6. Play one frame: Display a forward static frame. Click to run the application. Select the Hard Disk and click OK. 7. Back one frame: Display a backward static frame. 8. Pause: Pause the playback. 9. Forward Search: Fast play the recorded video to search an appointed image. 10. Stop: Stop the playback Note: The DVR’s HDD number will be next to your PC’s HDD number. If there is only one hard
Summary of the content on the page No. 16
Free Video Playback After selecting the appointed hard drive, click to select an event and click OK to play back the appointed surveillance. When you click the Event List icon, it pops-up an event table as the following illustration shows. You will see the table shows Record mode, Start time and End time of each event. Record Mode can be “T”, “M” or “S”. “T” represents Total Recording, which means the camera keeps on recording continually. “M” means Motion Recording, which means the
Summary of the content on the page No. 17
Users can backup or catch the data in DVR unit’s hard disks by saving Warranty Notice the recorded video as AVI files and play the files by Windows Media Player. Click to save an appointed surveillance video. After clicking the icon, LIMITED WARRANTY AVerMedia TECHNOLOGIES, Inc. warrants this product to be free of defects resulting from faulty a window shows to request the file name and directory. Click Save to manufacture or components under the following terms: start the recordin
